The HMC5883L magnetometer This component (a small chip) HMC5883L, produced by Honeywell, bases its operation on AMR (Anisotropic Magnetoresistive) technology and allows you to be able to measure both the direction and the magnitude of the earth’s magnetic field. This magnetometer HMC5883L has within 3 magneto-resistive sensors arranged on three perpendicular axes (the Cartesian axes x,
Welcome to my 3rd Instructable everyone ! Today we’re going to build a ‘device’ to control a mini-sized helicopter with a Wii Nunchuk. The helicopter that we’re using is a cheap (26$) 3-channel (yaw, throttle, pitch) helicopter that I bought a 1 month back from Dealextreme.com . I can say that it is a VERY
Nunchuk-controlled Helicopter using arduino Continue Reading
What are the characteristics of the ZelosLaser Engraver? Work area *Normal* 300mm x 200mm Housing dimensions Normal 440mm x 350mm x 220mm Work area *BIG MAMA* 660mm x 650mm Housing dimensions *BIG MAMA* 800mm x 800mm x 220mm Uses Arduino UNO Clone and a GRBL Shield 300mw 405nm Laser Diode There are 55x 3D-Printed parts
Affordable Opensource Arduino Laser Engraver for Everbody Continue Reading
I just hope every body’s heard. The Bird is the Word! This is a simple device to play Surfin Bird really loudly when someone trips off the motion sensor. If you don’t already own an Adafruit Wave Shield, I’d highly suggest purchasing one. It’s become my favorite shield by far. I love the idea of
Surfin’ Bird (Arduino Style) using arduino Continue Reading
Contents 1 Team Members 2 Mentor 3 Concept 4 Softwares Used 5 circuits 5.1 Pre Amp circuit 5.1.1 Circuit Diagram 5.1.2 Working 5.2 EEPROM circuit 5.3 Led Matrix display circuit 6 Algorithm for silence & noise removal 6.1 Pre-Emphasis 6.2 Silence and Noise Removal 6.2.1 Idea 6.2.2 Implementation 7 Codebook Formation 7.1 Database 7.2 Main
Voice Recognition System using arduino Continue Reading
This is a cute little project that takes a pumpkin, motion sensor, and some parts from Radio Shack. It was fun to create and build. This project was sponsored by the Radio Shack Great Create and I was able to make the whole thing with parts available from Radio Shack. Thanks for the gift card,
Arduino powered Haunted Pumpkin using arduino Continue Reading
This Instructable is about: building an automated photo booth. The total build cost was around $150 as I re-used a lot of the components and materials I already had in my garage – in addition to what I could salvage from scrap yards. Why? – I decided to build my own photo booth after trying
A Makers Wedding – Photo booth usnig arduino Continue Reading
Introduction Microcontrollers like the Arduino were designed to facilitate the use of electronics for designers and DIY enthusiasts. The interface provides a great starting points for a variety of elecronic circuit designs. However, as the microcontroller is standardized, it is also limited in its use. That shows for example in the limited number of PWM
Extending PWM output pins with a Texas Instruments TLC5940 LED driver using arduino Continue Reading
We are often asked on discussion boards, about conflicts between IRremote or IRLib and other Arduino Libraries. In this post, we present a sketch for ‘Simple Infrared PWM on Arduino’. This is the first part in a 3 part series of posts. Part 1 shows how to generate the simple Infrared carrier frequency on Arduino,
Simple Infrared PWM on Arduino Continue Reading
Hi Everybody In my first Instructable I want to show you how to build an cheap and easy Doorbell to Arduino ‘Interface’ so you can let your Arduinoproject get triggered through it or simply use your Arduino as a bell. Almost endless possibilities 😀 Step 1: What you need… Here’s what you’ll need, its not
Doorbell to Arduino ‘Interface’ Continue Reading
