flash Archives - Page 5 of 8 - Use Arduino for Projects

UCHIP: ARDUINO ZERO COMPATIBLE IN A NARROW DIP-16 PACKAGE!

Electronics News Updates / By Ibrar Ayyub

A very small narrow-DIP-sized, Arduino Zero compatible USB dev board (OTG enabled), with integrated buck and boost power supplies! The Arduino ecosystem provides an invaluable resource of hardware and software, which allows quick development of a myriad of projects thanks to its fruitful community. Several Arduino-compatible boards came out in the past years, to increase […]

UCHIP: ARDUINO ZERO COMPATIBLE IN A NARROW DIP-16 PACKAGE! Continue Reading

How to get sensor data from a remote Arduino via Wireless Lora Protocol

Electronics News Updates / By Ibrar Ayyub

This is an example to show how to get sensor data from a remote Arduino via Wireless Lora Protocol. The exampels requries below hardwares: 1) Client Side: Arduino + Lora Shield (868Mhz) + DS18B20 (Temperature Sensor). 2) Server Side: Arduino + Lora Shield (868Mhz) + Yun Shield + USB flash. make sure the USB

How to get sensor data from a remote Arduino via Wireless Lora Protocol Continue Reading

CH32 RISC-V MCUS GET OFFICIAL ARDUINO SUPPORT

Arduino News / By Ibrar Ayyub

Like many of you, we’ve been keeping a close eye on the CH32 family of RISC-V microcontrollers from WCH Electronics. You can get the CH32V003, featuring 2 kB RAM and 16 kB of flash for under fifteen cents, and the higher-end models include impressive features like onboard Ethernet. But while the hardware is definitely interesting,

CH32 RISC-V MCUS GET OFFICIAL ARDUINO SUPPORT Continue Reading

STUFFING A 32-PIN CHIP INTO A 28-PIN SOCKET

Arduino News / By Ibrar Ayyub

What’s the difference between a 64k ROM in a 28-pin DIP and a 128k ROM in a 32-pin DIP? Aside from the obvious answers of “64k” and “four pins,” it turns out that these two chips have a lot in common, enough so that it only takes a little bodging to make them interchangeable — more or

STUFFING A 32-PIN CHIP INTO A 28-PIN SOCKET Continue Reading

GREENLIANT DELIVERS ULTRA-FAST SPEEDS WITH NVME M.2 ARMOURDRIVE SSDS

Electronics News Updates / By Ibrar Ayyub

Greenliant has started sampling its NVMe M.2 ArmourDrive™ solid state drive (SSD) modules to customers requiring high-performance, high-capacity removable data storage that can withstand extreme environments. The new industrial temperature (-40°C to +85°C) 88 PX Series NVMe M.2 ArmourDrive SSDs use 3-bits-per-cell (TLC) 3D NAND flash memory and are built in the widely used 2242 and

GREENLIANT DELIVERS ULTRA-FAST SPEEDS WITH NVME M.2 ARMOURDRIVE SSDS Continue Reading

NORMAN – ARDUINO LIBRARY FOR CLIMATIC SIMULATION OF NATURAL DAYLIGHT, TEMPERATURE, AND HUMIDITY CYCLES

Electronics News Updates / By Ibrar Ayyub

Norman is a climatic simulation library designed to run on an Arduino Uno for indoor and greenhouse automation projects. Arduino Library for mathematical climatic simulation of natural daylight, temperature, and humidity cycles using minimal data sets. Given a set of parameters for a target locale, the library returns values for temperature, dew point, Relative Humidity, and

NORMAN – ARDUINO LIBRARY FOR CLIMATIC SIMULATION OF NATURAL DAYLIGHT, TEMPERATURE, AND HUMIDITY CYCLES Continue Reading

USING ESP32’S FLASH MEMORY FOR DATA STORAGE

Electronics News Updates / By Ibrar Ayyub

The ESP32 has about 4MB of internal flash memory and since the data stored within the flash memory is retained even when power is recycled, it becomes super useful for applications where you need to keep certain amount of data even after power off. For today’s tutorial, we will learn how to read and write

USING ESP32’S FLASH MEMORY FOR DATA STORAGE Continue Reading

F&S I.MX8X SOC FEATURES OPTIONAL INDUSTRIAL TEMP SUPPORT

Electronics News Updates / By Ibrar Ayyub

F&S Elektronik Systeme has announced specs for its “efus MX8X” module, which runs Linux on a dual- or quad-core -A35 i.MX8X SoC, and offers up to 2GB RAM and 64GB eMMC plus dual GbE, WiFi/BT, 4K video, and optional industrial temp support. The 2 x 47 x 11mm, 15-gram efus MX8X module is designed based on NXP’s low-powered i.MX8X. A host of efus-branded modules exploits

F&S I.MX8X SOC FEATURES OPTIONAL INDUSTRIAL TEMP SUPPORT Continue Reading

4DSYSTEMS – DIABLO16- AND PICASO-BASED LCD MODULES

Electronics News Updates / By Ibrar Ayyub

RS Components, a global multi-channel provider of industrial and electronic products and solutions, has introduced the Gen4 Series of integrated TFT LCD modules and related starter packs from embedded graphics specialist 4D Systems. Gen4 display modules are designed for ease of integration and use by electronics design engineers developing touch screen interfaces, achieving high functionality with a limited space requirement.

4DSYSTEMS – DIABLO16- AND PICASO-BASED LCD MODULES Continue Reading

NOVASOM LAUNCHES THE SBC-U1 IOT SBC BASED ON ESP32

Electronics News Updates / By Ibrar Ayyub

Novasom – the SBC manufacturing company, is famous for its two set of product lines, the U-Line for low power IoT devices and M-Line for multimedia processing based applications. Their products are Intel and ARM processors based for different applications and operating systems. Their latest board in the market is the SBC-U1 which is based on the popular ESP32. The SBC-U1 comes in two main variants. One with the name of Novasom

NOVASOM LAUNCHES THE SBC-U1 IOT SBC BASED ON ESP32 Continue Reading