Scintillino – an Arduino-based quick&dirty scintillation counter

Have you ever wondered about the radiation levels around you? Well today you can build your very own detector that measures ionizing radiation and displays data in real-time on an LCD (and also your computer if you want).
Scintillino
The visual design, as seen below, is perhaps a tad short of a Red Dot Award, but it sure works fine. It is a scintillation counter, no less and no more.

In fact, the game was all about doing it with the least amount of effort and nearly no budget, given that we already had a small scintillation crystal (LYSO) and a Silicon photomultiplier (SiPM) at hand. (Those were the only two expensive parts, at roughly $100 each. Sigh… We know…).

Our scintillator was supplied by Andy of http://pjtelect.com/. The SiPM is a KETEKone because they have a low breakdown voltage of 25V which makes it really cheap to bias them at around 30V….

What you will need:
– a scintillator crystal (we used a 1cmx1cmx2cm LYSO (Lu2Si2O7:Ce3+) but most any scintillation material should do)
– a Silicon photomultiplier (we prefer that over a PMT because HV biasing is easier and they are also harder to destroy)
– resistors, capacitors
– two fast rail2rail op-amps
– a simple DC-DC step-up converter off eBay
– a piezo buzzer for added dramatic effect
– Arduino Uno board
– LCD Keypad Shield (or another LCD, with minor adjustments to the Arduino sketch)
– soldering iron and tin (we use, lovingly, the old school non-ROHS stuff that will kill you etc etc yada yada)
– cardboard (for the motherboard), nylon ties
– a bunch of wires
– something to hold your SiPM tight against your crystal (we drilled holes into a scrap piece of thick plastic)

Now let’s get started!

Step 1: Setting up the scintillation detector

scintillation detector

Scintillators work by eating up a gamma-ray and then emitting a burst of several thousand photons of visible light within the next few nanoseconds. This meagre amount of visible light is detected by a Silicon photomultiplier and converted into a pulse of electrical current.

To measure light flashes this dim, we must obviously prevent any daylight from entering the detection chamber. For this reason we’ve constructed a cardboard box to enclose it.

Inside, we used a machined piece of thick plastic (because we had it, but duct tape or transparent epoxy would do, too) and some upholstery foam to press the scintillation crystal against the SiPM. You want good optical coupling here. The faces of the scintillator that are not facing the SiPM are wrapped in white teflon tape (yes, plumbing tape from HW store) to reflect as much light as possible toward the SiPM.

The top half of the box is a bit larger to fit over the bottom half. Make V cuts on both the bottom and the top half (as seen on the picture), so that you will be able to route the cables out of the box.

Tip: Depending on which you do first, the plastic or the box, make sure that the latter will fit the former.

Cover the scintillation thing with aluminium foil before closing the box. This will help keep out stray light….
… and your detector is ready!

Step 2: Some very high-fidelity nucleonics comin’ this way…

Front-end electronics.

The left side is the basic plain vanilla SiPM biasing circuit. Powered at 30V through the 10k resistor, with the ultra-fancy transimpedance stage being the 47ohm at left bottom. This is capacitively coupled to a two-stage discriminator that fires when the input pulse is large enough. Any fast rail-to-rail op-amp will do, and so does OPA2354 by Texas.

The hard part was soldering the darn smd package by hand to an old DIL socket. A shot of Gin steadied the hand and then all went well.

Ugly? Yes.
Works? Absolutely.

 

For more detail: Scintillino – an Arduino-based quick&dirty scintillation counter


About The Author

Ibrar Ayyub

I am an experienced technical writer holding a Master's degree in computer science from BZU Multan, Pakistan University. With a background spanning various industries, particularly in home automation and engineering, I have honed my skills in crafting clear and concise content. Proficient in leveraging infographics and diagrams, I strive to simplify complex concepts for readers. My strength lies in thorough research and presenting information in a structured and logical format.

Follow Us:
LinkedinTwitter

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top