I have created the framework for WiFi and voice control of a robot. The MKR1000 chip enables us to receive controls over WiFi. Things used in this project Hardware components Arduino MKR1000 × 1 DC motor (generic) × 2 Wheels × 1 SparkFun Dual H-Bridge motor drivers L298 × 1 9V battery (generic) × 1
This Wi-Fi controlled robot can be controlled from anywhere using the ARMA IoT shield for UNO and the Blynk App which provides the user interface. Overview Simple WiFi Controlled Robot Using ARMA IoT and Blynk! This project uses an Arduino Uno connected to the WiFi using an ARMA IoT shield and controlled
Wi-Fi Controlled Robot Using Arduino UNO And Blynk Continue Reading
Out of curiosity, I ordered the tiny ESP8266 relay switch from aliexpress.com but never knew it could be so embarrassing to find the right way to operate. The vendor said that the switching program is inbuilt and I only have to use some android phone to operate it. But despite several attempts with several Chinese
Tiny Wi-Fi Switch for $3 Continue Reading
Send status messages of your MKR1000 via Pushover service to your mobile phone, etc. Things used in this project Hardware components Arduino MKR1000 Story An IoT node must be trimmed to reduce current consumption due to battery life. A WiFi-based node as Arduino MKR1000 needs a lot of current while sending. To avoid a high
MKR1000 Pushover Status Continue Reading
How many mundane devices upgrade to IoT because they let you monitor a single data point or a variable? That little nudge over the communication precipice allows you to charge 500% more. Now, if you are as handy as a Hackaday reader, you can throw a lazy afternoon at the problem and get the same
Pushbutton → Push Notification Continue Reading
This project is a platform for drinking water monitoring and analytics, consists of IoT device, cloud, and mobile and web app. Things used in this project Hardware components Arduino MKR1000 × 1 PCF8574 × 1 AC-DC Module 5V 500mA × 1 10 Segment LED Bar Graph (Red) × 1 Resistor 100 ohm × 11 Resistor
Project “Gallon” – Smart Drinking Water Monitoring Platform Continue Reading
Restores your Wi-Fi connection for you, so you don’t have to, and keeps a track of how often this is done. Things used in this project Hardware components Arduino MKR1000 × 1 DFRobot DF Robot Lithium Polymer Battery (1000mAh, 3.7V) × 1 Jumper wires (generic) × 1 N-Channel Power Mosfet (STP36NF06L) × 1 Linear Regulator
Wi-Fi Power Toggler Continue Reading
We all know about Electricity energy meters which are installed in everyone’s house or offices to measure the electricity consumption. At last of every month, many of us get worried about the high electricity bill and we have to look at the energy meter once in a while. But what if we can monitor our
IoT Based Electricity Energy Meter using ESP12 and Arduino Continue Reading
A pen holder that determines when there are two or less pens and triggers an Amazon pen set replacement. Things used in this project Hardware components Arduino MKR1000 × 1 Crayola Air Dry Clay × 1 OpenBuilds Micro Limit Switch × 5 Software apps and online services Arduino IDE Amazon Web Services AWS SNS Hand
Amazon Dash Replenishment Pens Continue Reading
A device which collects data (environmental, soil and photosynthesis values) of plant(s) and then stores/analyze using a MKR1000 and Azure. Things used in this project Hardware components Arduino MKR1000 × 1 ADAFRUIT SD CARD READER × 1 ARDUCAM 5MP OV5642 × 1 SparkFun Weather Shield × 1 SparkFun Soil Moisture Sensor (with Screw Terminals) ×
PlantAnalyzer Continue Reading
Free Arduino projects, circuits, code and tutorials. Pick a board, pick a sensor, build something.
