Blog

Arduino INA219 load voltage and current measurement Proteus

INA219 Current & Voltage Sensor using Arduino Uno with Proteus Simulation

Blog, How To – DIY – Project Ideas, Other Project Ideas, Projects, Sensor – Transducer – Detector Project Ideas / By

Introduction This microcontroller project demonstrates how to measure load voltage and current using an Adafruit INA219 current sensor with an Arduino Uno in a Proteus simulation environment.It is a practical embedded systems example that shows real-time electrical measurements using I²C communication.Such projects are widely used in DIY electronics, power monitoring, and battery-powered systems.By combining Arduino, […]

INA219 Current & Voltage Sensor using Arduino Uno with Proteus Simulation Continue Reading

Trellis latching keyboard Proteus simulation

Adafruit Trellis Shield Latching Keyboard Test using ATmega328P with Proteus Simulation

Arduino Programmer Projects, Blog, How To – DIY – Project Ideas, Projects / By

Introduction This microcontroller project demonstrates how to use the Adafruit Trellis Shield as a latching LED keyboard with an ATmega328P in a Proteus simulation environment.The project focuses on reading button inputs over I2C and controlling LEDs in a clean, interactive way.It is a practical embedded systems example for learning key scanning, LED control, and I2C

Adafruit Trellis Shield Latching Keyboard Test using ATmega328P with Proteus Simulation Continue Reading

Arduino relay Proteus 4 channel relay module

Arduino 4 Channel Relay using ATmega328P with Proteus Simulation

Arduino News, Arduino Programmer Projects, Blog, Other Projects, Projects / By

Introduction This Arduino 4 Channel Relay project demonstrates how an ATmega328P-based Arduino can control multiple high-power devices using a relay interface.The system uses a ULN2003 driver IC to safely switch four 12V relays from low-voltage digital pins.Designed and tested using Proteus simulation, this project is ideal for learning relay interfacing, serial control, and embedded systems

Arduino 4 Channel Relay using ATmega328P with Proteus Simulation Continue Reading

Arduino DDS sinewave generator sinewave output using PWM and DDS technique

Arduino 168 DDS Sinewave Generator using ATmega168 with Proteus Simulation

Blog, Other Projects, Projects / By

Introduction This project demonstrates a DDS (Direct Digital Synthesis) sinewave generator implemented using an ATmega168 microcontroller in a Proteus simulation environment.The system generates a clean, adjustable sinewave using a lookup table and high-speed timer interrupts.By combining PWM output, timer-based sampling, and direct digital synthesis, this project shows how precise waveforms can be created using low-cost

Arduino 168 DDS Sinewave Generator using ATmega168 with Proteus Simulation Continue Reading

Arduino PWM simulation showing 16-channel PCA9685 PWM outputs

Arduino 16 Channel PWM Shield – PWM Test using ATmega328P with Proteus Simulation

Arduino PWM Project Ideas, Blog, Projects, PWM Projects / By

Introduction This microcontroller project demonstrates how to test and generate PWM signals using the Adafruit 16-Channel PWM/Servo Shield with an Arduino-compatible ATmega328P in a Proteus simulation environment.The project focuses on driving all 16 PWM outputs in a smooth wave pattern, making it ideal for learning multi-channel PWM control in embedded systems.Using the PCA9685 12-bit PWM

Arduino 16 Channel PWM Shield – PWM Test using ATmega328P with Proteus Simulation Continue Reading

Arduino RGB ShiftPWM PWM lighting effects in Proteus

Arduino & RGB Common Anode LED ShiftPWM using Arduino Uno with Proteus Simulation

Blog, LED Projects / By

Introduction This microcontroller project demonstrates how to control multiple RGB common anode LEDs using an Arduino Uno and ShiftPWM through shift registers in a Proteus simulation environment.Instead of using many Arduino pins, the design efficiently expands outputs using shift registers while still achieving smooth PWM-based color control.The project showcases advanced LED fading, color transitions, hue

Arduino & RGB Common Anode LED ShiftPWM using Arduino Uno with Proteus Simulation Continue Reading

Arduino IR Proteus Simulation IR receiver TSOP4838 connection

Arduino Infra-Red Remote using Arduino Uno with Proteus Simulation

Blog, Other Project Ideas, Projects / By

Introduction This microcontroller project demonstrates how to capture and analyze raw infrared (IR) data from a Keyes IR remote using the NEC protocol. Built around an Arduino Uno, the project focuses on decoding IR signals and displaying detailed timing and protocol information via serial output.It is especially useful for learners exploring Proteus simulation, embedded systems,

Arduino Infra-Red Remote using Arduino Uno with Proteus Simulation Continue Reading

Arduino IoT LED control circuit diagram using Arduino Uno and Yun Shield

Yun Shield – Toggle an LED using Arduino Uno with Proteus Simulation

Arduino LED Project Ideas, Arduino Programmer Projects, Blog, LED Projects, Projects / By

Introduction This microcontroller project demonstrates how to toggle an LED using an Arduino Uno and a Yun Shield, controlled from a mobile device. It is a simple but powerful introduction to Internet of Things (IoT) concepts using Proteus simulation and visual programming.The project shows how physical hardware like an LED can be controlled remotely, making

Yun Shield – Toggle an LED using Arduino Uno with Proteus Simulation Continue Reading

STM32 BluePill LCD project flowchart for Proteus simulation

Arduino-STM32 BluePill LCD Display using STM32 BluePill with Proteus Simulation

Arduino LCD Project Ideas, Blog, LCD Projects, Projects / By

Introduction This microcontroller project demonstrates how to interface a standard alphanumeric LCD with the STM32 BluePill using Arduino-STM32 (Visual Designer) in a Proteus simulation environment.The project is a simple yet powerful starting point for anyone working with embedded systems, DIY electronics, or STM32-based designs.It focuses on displaying text messages on an LCD, proving correct GPIO

Arduino-STM32 BluePill LCD Display using STM32 BluePill with Proteus Simulation Continue Reading

HW(4.0) – Arduino and Microcontrollers: Microcontroller Morse Code System

Blog, LED Projects / By

Ideation and Design: Microcontroller Morse Code System development initially aimed to create a functional Microcontroller Fidget Keyboard System by linking mechanical switches to a microcontroller. This section explains how the system captures and interprets button presses to convert user input into Morse code. This led to an early pivot in design, driven by practical challenges

HW(4.0) – Arduino and Microcontrollers: Microcontroller Morse Code System Continue Reading

Scroll to Top