Comptine Chapeau à l'aide d'arduino

Plug your FTDI and battery into the main board and coonect it to your computer with your USB cable.  Upload your code.

/*
Nursery Rhyme Hat
Liz Huessy
March 2014
*/
int ledPin =
int ledPin = A3;  // The white LED pin is connected to pin A3
int redPin = 10;  // The red LED pin is connected to pin 10
int bluePin = 9;  // The blue LED pin is connected to pin 9
int greenPin = 6;// The green LED pin is connected to pin 6
int ground = 11; // Pin 11 is the ground pin
int speakerPin = A2;     // The speaker is connected to digital pin A2
int sensorPin = A4;     // The light sensor is connected to pin A4
int sensorValue;     // Variable to store the value coming from the sensor

void setup()
{

pinMode(speakerPin, OUTPUT);     // Sets this pin to be an output
pinMode(A3, OUTPUT);  // Sets this pin to be an output
pinMode(10, OUTPUT);  // Sets this pin to be an output
pinMode(9, OUTPUT);  // Sets this pin to be an output
pinMode(6, OUTPUT);   // Sets this pin to be an output
pinMode(sensorPin, INPUT); //
pinMode(ground, OUTPUT);
digitalWrite(ground, LOW);  // Turns off power to pin 11 (ground)

}

void loop()     // Runs on a loop
{

sensorValue = analogRead(sensorPin);     // Read the value from the sensor
delay(100);     // Delay for 1/10 of a second

if (sensorValue < 20)// If it is dark, turn all LEDs off
{
digitalWrite(6, LOW);
delay(750);
digitalWrite(9, LOW);
delay(500);
digitalWrite(10, LOW);
delay(500);
digitalWrite(A3, LOW);
delay(500);
}
else {  //If it is not dark, turn green and blue LEDs on and play the tune, then turn on red and white LEDs
digitalWrite(6, HIGH);
delay(500);
digitalWrite(9, HIGH);
delay(500);
scale();     // Call the scale() function
delay(1000);     // Delay for 1 second
digitalWrite(10, HIGH);
delay(500);
digitalWrite(A3, HIGH);
delay(500);

}
}
void beep (unsigned char speakerPin, int frequencyInHertz, long timeInMilliseconds)     // the sound producing function
{
int x;
long delayAmount = (long)(1000000/frequencyInHertz);
long loopTime = (long)((timeInMilliseconds*1000)/(delayAmount*2));
for (x=0;x<loopTime;x++)
{
digitalWrite(speakerPin,HIGH);
delayMicroseconds(delayAmount);
digitalWrite(speakerPin,LOW);
delayMicroseconds(delayAmount);
}
}

void scale ()//Play Mary Had a Little Lamb
{
beep(speakerPin,2637,500);  //E
beep(speakerPin,2349,500);  //D
beep(speakerPin,4186,500);  //C
beep(speakerPin,2349,500);  //D
beep(speakerPin,2637,500);  //E
beep(speakerPin,2637,500); //E
beep(speakerPin,2637,1000); //E

beep(speakerPin,2349,500);  //D
beep(speakerPin,2349,500);  //D
beep(speakerPin,2349,500);  //D
beep(speakerPin,2637,500);  //E
beep(speakerPin,2637,500);  //E
beep(speakerPin,2637,1000);  //E

beep(speakerPin,2637,500);  //E
beep(speakerPin,2349,500);  //D
beep(speakerPin,4186,500);  //C
beep(speakerPin,2349,500);  //D
beep(speakerPin,2637,500);  //E
beep(speakerPin,2637,500); //E
beep(speakerPin,2637,1000); //E

beep(speakerPin,2637,500);  //E
beep(speakerPin,2349,500);  //D
beep(speakerPin,2349,500);  //D
beep(speakerPin,2637,500);  //E
beep(speakerPin,2349,500);  //D
beep(speakerPin,4186,1000);  //C
beep(speakerPin,4186,1000);  //C
}

Once I had written my code, the next thing I did was to create a diagram of my e-textile, showing the exact connections and layout of my circuit, making sure that no negative and positive lines crosssed and that each LED, Buzzer and Sensor was properly connected.
It is very important to complete this step before taking apart the Lilypad pieces!