Quick and Easy Arduino Nightlight

Honestly, how many people have been in this scenario (leave a yes or no in the comments) : It is 2:30 in the morning and you wake up with a need to do something whatever that may be (bathroom, forgotten homework assignment, project due in 5 or 6 hours, etc.) it takes you 5-10 minutes to find the light switch (give or take…)
Quick and Easy Arduino Nightlight
My mother likes a night light for the bathroom but she didn’t want one that stayed on all night so I needed one that could detect a person. Many thoughts popped up into my head on what sensors to use. I could us esuch as the Linescan Imaging Sensor Daughterboard by Parallax but that was overkill and too expensive. A cheaper solution would be to use a few ir leds with ir phototransistor but still too complicated. I also thought of the Ping Sensor from Parallax but too hard to program with my beginner standards in C and, it used too much power. (I’m more of a Spin and Assembly language person.) I finally looked through my sensors box and found…(…drumroll please…) …Parallax’s Passive Infared Motion Sensor! It was fairly inespensive ($9.99), it could work in the dark, and, I have had experience in programming these!

Step 1: Get The Required Materials.

1 of everything except where noted.

Arduino
PIR Motion Sensor from Parallax
LED ( Preferably Ultra Bright White. I bought mine along with other colors at Ebay from this seller: http://myworld.ebay.com/led.shop*2010/?_trksid=p4340.l2559

They will compile your own personal mix of colors if you want them to…they will charge more but it is a personalized order. I also found this order of only white LEDs but very cheap.

http://www.ebay.com/itm/100pcs-5mm-Ultra-Bright-White-LEDs-200pcs-resistors-/220610858794?pt=LH_DefaultDomain_0&hash=item335d6e8f2a#ht_2715wt_1017

Many jumper wires

Optoisolator/ optocoupler/ relay

Resistor. Define the value yourself.

Step 2: Program.

Program.

Program the code into the Arduino.

This will make the Arduino read the sensor’s output and trigger an LED for seven seconds and turn off. Modify to meet your needs. It takes 30 seconds to calibrate the sensor.

Use this link and download open the editor and program.

https://www.rapidshare.com/#!download|833tl3|3411132297|Sketch.pde|1|R~2964C5D605113ECA37CDDB4ED2C02EFB|0|0

If you have trouble…here it is!

//be sure the project box is insulated or false motion triggers will happen
int calibrationTime = 30;
int Time = 0;
long unsigned int lowIn;
long unsigned int pause = 5000;
boolean lockinHigh = false;
int LEDsop = 13; // pin 13 includes resistor sop- signal out pin
int outpin = 12; // for any other device that doesn’t require resistor
int SensorInpin = 2; // can vary, must be digital from 1-12
boolean sensorready = false;
void setup (){
pinMode (LEDsop, OUTPUT);
digitalWrite (LEDsop, LOW);
pinMode (outpin, OUTPUT);
digitalWrite (outpin, LOW);
pinMode (SensorInpin, INPUT);
pinMode (0, INPUT);
pinMode (1, INPUT);
pinMode (3, INPUT);
pinMode (4, INPUT);
pinMode (5, INPUT);
pinMode (6, INPUT);
pinMode (7, INPUT);
pinMode (8, INPUT);
pinMode (9, INPUT);
pinMode (10, INPUT);
pinMode (11, INPUT);
do {
digitalWrite (LEDsop, HIGH);
delay (500);
digitalWrite (LEDsop, LOW);
delay (500);
Time = Time + 1;
}
while (Time < calibrationTime);
digitalWrite (LEDsop, LOW); //if led turns off, sensor is ready
sensorready = true;
}
void loop (){
if (sensorready == true){
if (digitalRead(SensorInpin))
{
digitalWrite (LEDsop, HIGH);
digitalWrite (outpin, HIGH);
delay (7000); //modify to meet your required delay time
digitalWrite (LEDsop, LOW);
digitalWrite (outpin, LOW);
delay (250);
}
}
}

Step 3: Assemble.

Plug the sensor’s power pin (red) to 5 volts, the ground (black) to ground and the signal (white) to digital pin 2.

Add the LED to Pin 13. Make a note of it as in the troubleshooting step I will discuss this.

Solder (or breadboard the optoisolator if you need any more than one LED to turn on.) This is connected to Pin 12.

Use the relay if necessary. This is also for Pin 12.

Make sure the sensor’s jumper is towards the H position.

 

For more detail: Quick and Easy Arduino Nightlight


About The Author

Ibrar Ayyub

I am an experienced technical writer holding a Master's degree in computer science from BZU Multan, Pakistan University. With a background spanning various industries, particularly in home automation and engineering, I have honed my skills in crafting clear and concise content. Proficient in leveraging infographics and diagrams, I strive to simplify complex concepts for readers. My strength lies in thorough research and presenting information in a structured and logical format.

Follow Us:
LinkedinTwitter

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top