How to Build an Arduino Circuit on a Breadboard

Small Kit with Big Functionality

By Ryan Winters
Product Manager

There are many reasons to build your own Arduino circuit on a breadboard or PCB. It takes less space, projects don’t always require every pin to be used on the I/O headers, or maybe you won’t be using a shield but you still want Arduino as the brain of your project. The following steps will outline how to assemble the circuit on a breadboard. I am borrowing the majority of the walk-through from the Arduino site and recommend you purchase Jameco’s Barebones Arduino Circuit Kit. You can order the components separately or save a little money by ordering this kit. The breadboard is not included in the kit.

 How to Build an Arduino Circuit on a Breadboard

This Kit Includes:

Qty. Part Description Mfr. Part No.
1 IC, ATmega328P A000048
1 Socket, IC, 28-pin, 0.3″ 390261-9
1 IC, 5V Regulator, 7805T 7805T
1 LED, Red, 660nm, T1-3/4 UT1871-81-M1-R
1 LED, Green, 565nm, T1-3/4 MCDL-5013GD
1 Resistor, 1/4W, 10KΩ CF1/4W103JRC
2 Resistor, 1/4W, 180Ω CF1/4W181JRC
2 Capacitor, radial, 10µF, 50V R10/50
1 Crystal, 16MHz, low-profile TQR49S16M0000A2010
2 Capacitor, ceramic disc, 22pF, 50V DC22
1 Capacitor, ceramic disc, 0.1µF, 50V DC.1
1 Switch, pushbutton, OFF-(ON) TL1105-A
1 Header, 6-pin, 1 row, vertical, 0.1″ JS1109-6-R
1 IC, 3.3V Regulator, LM1117T-3.3 LM1117T-3.3/LD1117V33
2 Capacitor, tantalum, 10µF, 25V TM10/25

Other components you may need:

Qty. Part Description Mfr. Part No.
1 Wire, Hook-up, 22 AWG solid, 100′, Blue 9313-LB-R
1 Wire Jumper kit, 22AWG, 70pcs, 14 lengths, pre-stripped WJW-70B-5
1 Breadboard, 830 point, 6.5″ x 2.125 WBU-202-R
1 FTDI Breakout board, 5V, USB to Serial 50512
1 Power Supply, Wall adapter, 9V @ 1.2A S15AD090150H0650-R
1 DC Power Jack, 2.1mm 722A
1 Battery holder w/ cover & switch, 9V, 6″ wires SBH-9VAS
1 Battery, Energizer 9V ALK 9V 522

Step 1: Parts Inventory

Start by laying out the pieces in your kit.

Step 2: Add Power Supply Components

The Arduino power jack can accept an input voltage range of 7 to 16 volts. The most common input sources are a trusty 9V battery or a 9-12VDC power supply. Because most sensors and chips require a 5V source, we will need the 7805T voltage regulator to cut the 9V down to a component friendly 5V. If you connect more than 16V, you risk damaging the IC.

A. Add the power and ground jumper wires where the voltage regulator will be as shown below.

B. Next, add power and ground wires at the bottom of the breadboard to connect the ground rails and the power rails together as pictured.

 How to Build an Arduino Circuit on a Breadboard

C. The 7805 voltage regulator is a TO-220 package. The positive input from the external power source will connect with the component facing you (printed side) and the leads pointing down the first pin (left side). The middle pin is ground (negative) and the third pin (right side) is the 5V output side. Add wires to connect the output side of the regulator to the power rail of the breadboard and the ground to the ground rail.

D. Add the 10µF decoupling capacitors between the input power and ground, and also on the output side between the power rail and the ground rail. The capacitors are polarized; the negative side goes to ground and the other pin goes to the positive voltage.

E. Place the power LED close to the input source and at the top of the breadboard. You can use the green or red LED. Connect a jumper wire from the negative lead (short leg) of the LED to the ground rail and install a 180Ω resistor from the positive LED lead (long leg) to the power rail.

 

For more detail:  How to Build an Arduino Circuit on a Breadboard


About The Author

Ibrar Ayyub

I am an experienced technical writer holding a Master's degree in computer science from BZU Multan, Pakistan University. With a background spanning various industries, particularly in home automation and engineering, I have honed my skills in crafting clear and concise content. Proficient in leveraging infographics and diagrams, I strive to simplify complex concepts for readers. My strength lies in thorough research and presenting information in a structured and logical format.

Follow Us:
LinkedinTwitter

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top